Book A Free Estimate

Just about everyone has got his or her own piece of advice when it comes to How to Install a Bathtub.

Setting up a tub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is conveniently obtainable, the project can move rapidly; if you need to open up a wall to eliminate the old bathtub as well as position the new bathtub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will need an assistant to vacate the old tub and set in the brand-new one. Make certain you have qualified yourself for the job as well as are comfortable trying it. As opposed to working with a professional to take control of a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly help you mount a new tub in your bathroom if you have already acquired a new bathtub and don't need to transform the setup of your previous water system pipes.
Your tools and also material checklist need to comprise the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been removed, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before moving on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

Suitable New Touches

If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin making sure that the washers are in area between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

Mounting the Bath tub

Using both wooden boards under its feet, put the bath tub in the needed setting. The wood boards are practical in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile tap adapter to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Activate the water system and inspect all joints and also new pipework for leaks and tighten them if essential. Load the tub as well as also check the overflow electrical outlet as well as the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub should wait till the bathtub has actually been used at the very least once as this will certainly resolve it into its final placement.

Getting ready for the Installment

First of all, the sustaining frame supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the provided washers.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final setting.

Tiling Around the Bath tub

In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to crack a stiff seal, creating the water to pass through the wall between the bath as well as the tiling, causing difficulties with wetness and possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealant can break fairly very early if you do not take into account this activity prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or water resistant glue and cement.

Bathtub Installation

How Important Is A Bathtub To Your Home?

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

Install Piping Before Tub

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

Position the Tub

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

Assemble Drain Connections

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

Place a Pipe For the Shower Head

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

Attaching Hot and Cold Water Lines

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

Install the Spout

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

Check For Leaks

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

estore the Bathroom Wall

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

Hopefully you liked our topic about How to Install a Bathtub. Thanks a ton for taking a few minutes to read our article. Appreciated our write up? Please share it. Let someone else discover it. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Quick resolutions for plumbing disruptions.